Bucket: regassist   Key: v2/targeted-fetch/water/us/tdf_101f4bfa3df3f01d23d007b0142abb81/content.md
Source: https://www.epa.gov/eg/plastics-molding-and-forming-effluent-guidelines

Dot gov Official websites use .gov
A .gov website belongs to an official government organization in the United States. HTTPS Secure .gov websites use HTTPS
A lock (Lock A locked padlock) or https:// means you’ve safely connected to the .gov website. Share sensitive information only on official, secure websites.

Plastics Molding and Forming Effluent Guidelines

The EPA promulgated the Plastics Molding and Forming Effluent Guidelines and Standards (40 CFR Part 463Exit EPA’s website) in 1984. The regulation covers direct dischargersdirect dischargersA point source that discharges pollutants to waters of the United States, such as streams, lakes, or oceans.. The Effluent Guidelines and Standards are incorporated into NPDES permits. On this page: * What is the Plastics Molding and Forming Industry? * Related Categories * Rulemaking History * Additional Information

What is the Plastics Molding and Forming Industry?

The plastics molding and forming (PM &F) industry is a large and diversified industry that uses plastic materials to produce a wide variety of consumer and industrial products. The product markets include automobiles, appliances and electronics, construction materials, disposables, household furnishings, housewares, and medical products. Related Information * Stormwater Fact Sheet (Sector Y: Rubber, Miscellaneous Plastic Products, and Miscellaneous Manufacturing Industries)

There are many different types of production processes that process various combinations of raw materials. PM&F plants blend, mold, form, or otherwise process plastic materials into intermediate or final plastic products. They include commonly recognized processes such as extrusion, molding, coating and laminating, thermoforming, calendering, casting, foaming, cleaning, and finishing. Process water is used in PM&F plants to cool or heat the plastic products; to clean the surfaces of both the plastic products and the equipment used to produce those products; and to finish plastic products. At the time of the 1984 rulemaking there were approximately 10,260 PM&F facilities in the United States, of which 810 were direct dischargers. (There were also 1,145 indirect dischargers, which are subject to the General Pretreatment Regulation at 40 CFR Part 403Exit EPA’s website.) PM&F activities are included within NAICS group 3261, Plastics Product Manufacturing.
(Note: the NAICS listing is provided as a guide and does not define the coverage of the PM&F category. For precise definitions of coverage, see the applicability sections in 40 CFR Part 463Exit EPA’s website.)

Wastestreams

The PM&F regulation covers process wastewater. Non-contact cooling water (water that does not contact either the plastic product or equipment surfaces that have contacted the plastic product) is not covered by the regulation, but may be addressed in individual permits on a case-by-case basis. The PM&F regulation does not apply to the following: * wastewater generated during the reticulation of polyurethane foam * processes used to produce regenerated cellulose * molding and forming operations that process regenerated cellulose.

Pollutants covered

Regulation Subcategories

Processes that coat a plastic material onto a substrate may fall within the definition of Electroplating category (40 CFR Part 413Exit EPA’s website) and Metal Finishing (40 CFR Part 433)Exit EPA’s website. These coating operations are excluded from those categories and are included in the PM&F category. See 40 CFR 433.10(b)Exit EPA’s website. Coating of plastic material onto a formed metal substrate is also covered by the PM&F regulation and is not covered by the specific metal forming effluent guidelines such as those for Aluminum Forming (40 CFR Part 467Exit EPA’s website), Copper Forming (40 CFR Part 468Exit EPA’s website), and Nonferrous Metals Forming (40 CFR Part 471Exit EPA’s website). However, the PM&F regulation applies only to the coating process; the prior forming operations are subject to the specific metal forming regulation. Some molding and forming processes (e.g., extrusion and pelletizing) are used by plastic resin manufacturers to process crude intermediate plastic material. Plastics molding and forming processes used by plastic resin manufacturers to process crude intermediate plastic materials for shipment off-site are excluded from the PM&F regulation and are regulated under the Organic Chemicals, Plastics and Synthetic Fibers category (OCPSF ; 40 CFR Part 414Exit EPA’s website). Plastics molding and forming processes used by plastic resin manufacturers to process crude intermediate plastic materials, which are then further processed on-site into intermediate or final plastic products by molding and forming, are controlled by the PM&F regulation.

Rulemaking History

1984 Initial Rulemaking

Additional Information

For additional information regarding Plastics Molding and Forming Effluent Guidelines, please contact Samantha Lewis (lewis.samantha@epa.gov) or 202-566-1058.

Effluent Guidelines

Open Sidenav Menu Close Sidenav Menu Contact Us About Effluent Guidelines Contact Us About Effluent Guidelines to ask a question, provide feedback, or report a problem. Last updated on March 6, 2026 Welcome! Please share your feedback on how we can make www.epa.gov work better for you. A red asterisk (*) indicates a required field.

Success

Thank you. Your feedback has been received.

Error

alert message Required Questions - page 1 of 2 question_55203_answer_01 How would you rate your experience on www.epa.gov today? *

0 Stars 1 Star 2 Stars 3 Stars 4 Stars 5 Stars Please explain the reason for your rating. * 400 characters allowed Would you like to take two more minutes to answer more questions to help us improve our services? Yes, keep going → No, only submit these responses Optional questions - page 2 of 2 How would you describe yourself? Business Government employee Scientist Student Other Enter other text Please tell us why you visited www.epa.gov today. 400 characters allowed Did you visit www.epa.gov to accomplish a specific task? If yes, please explain why you were able or unable to accomplish your task. 400 characters allowed How can we make www.epa.gov a more helpful website? 400 characters allowed Submit [NAICS]: North American Industrial Classification System [*]: required